Arctic White Glass Splashback 900x750

IMPORTANT Unfitted glass is fragile. Do not place on hard surfaces prior to fitting. Special care should be taken with the corners of the product as impact will cause the product to crack. To prevent product failures ensure that:  All fitting steps are completed. A space of at least 2mm is left between the product and all surfaces. The gaps must be filled with silicone. The surface to which the product is applied is flat, variations in level in excess of 5mm should be packed with silicone prior to fitting. You do not use any form of adhesive other than silicone as certain adhesives will degrade the finish of the glass.   SAFE HANDLING OF GLASS All products are supplied with a safety backing but we recommend that glass is handled with care and in particular eye protection and suitable gloves should be worn.   AFTER CARE Do not use abrasive cleaners. For the best results use: Hot water with a mild soap detergent.   BEFORE YOU START Check that all components are present. Ensure that you have all tools to hand.   TOOLS NEEDED TO FIT THE SPLASH BACK Tape measure. Sealant gun. Silicone sealant - only use LM or AC. (Our Splashbacks are self adhesive, the Silicone Sealant is for sealing gaps only) 2mm tile spacers.   CHECK LIST Do you have everything you need to start the job? Check that the splash back fits. Ensure that your worktop is fitted securely. Check that your worktop is level. Clear all dust from the worktop. Ensure that your hob is fitted in accordance with the manufacturer's instructions and that the clearance between the hob and splash back complies with the appliance manufacturer's instructions. Make sure that your extractor is securely fitted in accordance with the manufacturer's instructions.   DO NOT Fit the splash back directly onto a hob or work surface useing spacers. Place the splash back on its edge on any hard surface during the fitting process. Use the product until the silicone has cured (follow the manufacturer's instructions).

 82.99
More Information
 

Zest Glass Splashback 900x750

IMPORTANT Unfitted glass is fragile. Do not place on hard surfaces prior to fitting. Special care should be taken with the corners of the product as impact will cause the product to crack. To prevent product failures ensure that:  All fitting steps are completed. A space of at least 2mm is left between the product and all surfaces. The gaps must be filled with silicone. The surface to which the product is applied is flat, variations in level in excess of 5mm should be packed with silicone prior to fitting. You do not use any form of adhesive other than silicone as certain adhesives will degrade the finish of the glass.   SAFE HANDLING OF GLASS All products are supplied with a safety backing but we recommend that glass is handled with care and in particular eye protection and suitable gloves should be worn.   AFTER CARE Do not use abrasive cleaners. For the best results use: Hot water with a mild soap detergent.   BEFORE YOU START Check that all components are present. Ensure that you have all tools to hand.   TOOLS NEEDED TO FIT THE SPLASH BACK Tape measure. Sealant gun. Silicone sealant - only use LM or AC. (Our Splashbacks are self adhesive, the Silicone Sealant is for sealing gaps only) 2mm tile spacers.   CHECK LIST Do you have everything you need to start the job? Check that the splash back fits. Ensure that your worktop is fitted securely. Check that your worktop is level. Clear all dust from the worktop. Ensure that your hob is fitted in accordance with the manufacturer's instructions and that the clearance between the hob and splash back complies with the appliance manufacturer's instructions. Make sure that your extractor is securely fitted in accordance with the manufacturer's instructions.   DO NOT Fit the splash back directly onto a hob or work surface useing spacers. Place the splash back on its edge on any hard surface during the fitting process. Use the product until the silicone has cured (follow the manufacturer's instructions).

 107.99
More Information
 

Red Glass Splashback 1000x750

IMPORTANT Unfitted glass is fragile. Do not place on hard surfaces prior to fitting. Special care should be taken with the corners of the product as impact will cause the product to crack. To prevent product failures ensure that:  All fitting steps are completed. A space of at least 2mm is left between the product and all surfaces. The gaps must be filled with silicone. The surface to which the product is applied is flat, variations in level in excess of 5mm should be packed with silicone prior to fitting. You do not use any form of adhesive other than silicone as certain adhesives will degrade the finish of the glass.   SAFE HANDLING OF GLASS All products are supplied with a safety backing but we recommend that glass is handled with care and in particular eye protection and suitable gloves should be worn.   AFTER CARE Do not use abrasive cleaners. For the best results use: Hot water with a mild soap detergent.   BEFORE YOU START Check that all components are present. Ensure that you have all tools to hand.   TOOLS NEEDED TO FIT THE SPLASH BACK Tape measure. Sealant gun. Silicone sealant - only use LM or AC. (Our Splashbacks are self adhesive, the Silicone Sealant is for sealing gaps only) 2mm tile spacers.   CHECK LIST Do you have everything you need to start the job? Check that the splash back fits. Ensure that your worktop is fitted securely. Check that your worktop is level. Clear all dust from the worktop. Ensure that your hob is fitted in accordance with the manufacturer's instructions and that the clearance between the hob and splash back complies with the appliance manufacturer's instructions. Make sure that your extractor is securely fitted in accordance with the manufacturer's instructions.   DO NOT Fit the splash back directly onto a hob or work surface useing spacers. Place the splash back on its edge on any hard surface during the fitting process. Use the product until the silicone has cured (follow the manufacturer's instructions).

 64.98
More Information
 

Galaxy Speckle Glass Splashback 900x750

IMPORTANT Unfitted glass is fragile. Do not place on hard surfaces prior to fitting. Special care should be taken with the corners of the product as impact will cause the product to crack. To prevent product failures ensure that:  All fitting steps are completed. A space of at least 2mm is left between the product and all surfaces. The gaps must be filled with silicone. The surface to which the product is applied is flat, variations in level in excess of 5mm should be packed with silicone prior to fitting. You do not use any form of adhesive other than silicone as certain adhesives will degrade the finish of the glass.   SAFE HANDLING OF GLASS All products are supplied with a safety backing but we recommend that glass is handled with care and in particular eye protection and suitable gloves should be worn.   AFTER CARE Do not use abrasive cleaners. For the best results use: Hot water with a mild soap detergent.   BEFORE YOU START Check that all components are present. Ensure that you have all tools to hand.   TOOLS NEEDED TO FIT THE SPLASH BACK Tape measure. Sealant gun. Silicone sealant - only use LM or AC. (Our Splashbacks are self adhesive, the Silicone Sealant is for sealing gaps only) 2mm tile spacers.   CHECK LIST Do you have everything you need to start the job? Check that the splash back fits. Ensure that your worktop is fitted securely. Check that your worktop is level. Clear all dust from the worktop. Ensure that your hob is fitted in accordance with the manufacturer's instructions and that the clearance between the hob and splash back complies with the appliance manufacturer's instructions. Make sure that your extractor is securely fitted in accordance with the manufacturer's instructions.   DO NOT Fit the splash back directly onto a hob or work surface useing spacers. Place the splash back on its edge on any hard surface during the fitting process. Use the product until the silicone has cured (follow the manufacturer's instructions).

 90.49
More Information
 

Zest Glass Splashback 1000x750

IMPORTANT Unfitted glass is fragile. Do not place on hard surfaces prior to fitting. Special care should be taken with the corners of the product as impact will cause the product to crack. To prevent product failures ensure that:  All fitting steps are completed. A space of at least 2mm is left between the product and all surfaces. The gaps must be filled with silicone. The surface to which the product is applied is flat, variations in level in excess of 5mm should be packed with silicone prior to fitting. You do not use any form of adhesive other than silicone as certain adhesives will degrade the finish of the glass.   SAFE HANDLING OF GLASS All products are supplied with a safety backing but we recommend that glass is handled with care and in particular eye protection and suitable gloves should be worn.   AFTER CARE Do not use abrasive cleaners. For the best results use: Hot water with a mild soap detergent.   BEFORE YOU START Check that all components are present. Ensure that you have all tools to hand.   TOOLS NEEDED TO FIT THE SPLASH BACK Tape measure. Sealant gun. Silicone sealant - only use LM or AC. (Our Splashbacks are self adhesive, the Silicone Sealant is for sealing gaps only) 2mm tile spacers.   CHECK LIST Do you have everything you need to start the job? Check that the splash back fits. Ensure that your worktop is fitted securely. Check that your worktop is level. Clear all dust from the worktop. Ensure that your hob is fitted in accordance with the manufacturer's instructions and that the clearance between the hob and splash back complies with the appliance manufacturer's instructions. Make sure that your extractor is securely fitted in accordance with the manufacturer's instructions.   DO NOT Fit the splash back directly onto a hob or work surface useing spacers. Place the splash back on its edge on any hard surface during the fitting process. Use the product until the silicone has cured (follow the manufacturer's instructions).

 64.98
More Information
 

BOND IT Xtreme Anti Mould Silicone Sealant 310ml White

BOND IT Xtreme Anti-Mould Silicone Sealant 310ml - White - BDSANX-WH A specially formulated sealant containing fungicide for sanitary applications in areas of high humidity. One part silicone sealant with excellent primerless adhesion to enamel, tiles, glazed ceramic, glass, stainless steel, polycarbonate glass (Plexiglass) and acrylics. can also be used on wood, aluminium, chrome, concrete, brick and PVC when used in conjunction with a primer. Bond It XTREME ALWAYS contains a biocide to prevent unsightly mould growth. Bond It XTREME ALWAYS can be used in swimming pool areas (but not in swimming pools). Ideal for sanitary applications including connection and expansion joints in bath rooms, kitchens, toilet areas and swimming pool areas. Benefits: high resistance to chemicals. good tooling characteristics. Permanently flexible. Due to the large number of existing paint systems, it is necessary to conduct a compatibility test to ensure suitability. There is also danger of yellowing on contact with white alkyd resin paints. Risk of corrosion when used on bare iron or non-ferrous metals. Size - 310ml Fungal Resistant Life - 25 Years

 10.90
More Information